M-Audio DELTA 1010LT Specifications download pdf (Page 22)

Patchbay/Router Page

The Patchbay/Router page allows you to connect each of the Delta 1010LT’s hardware

outputs (4 pairs of analog outputs and 1 pair of digital output channels) to specific audio

sources within the Delta 1010LT board. To display this page, click the "Patchbay/Router"

tab of the Delta Control Panel.

The leftmost vertical column of Patchbay/Router page, "H/W Out 1/2," connects this

analog stereo pair to one of eight stereo sources:

1. The default setting, "WavOut 1/2," connects ports OUT1 and OUT2 to your

music software or Windows multimedia applet. In other words, when music

software plays audio to the device named "WavOut 1/2 Delta-1010LT" it will

be routed directly to the "hardware" analog outputs 1 & 2 of your 1010LT

breakout cable.

2. The second option, "Monitor Mixer," connects ports OUT1 and OUT2 to the

outputs of the Delta 1010LT monitor mixer. For more information of the

capabilities of the monitor mixer, please see the section "Monitor Mixer Page."

3. The third option, "S/PDIF In," connects ports OUT1 and OUT2 directly to

the hardware S/PDIF input on the Delta 1010LT PCI host card. The left

channel of the S/PDIF In is routed to OUT1 and the right channel of the

S/PDIF In is routed to OUT2.

4. The fourth option, "S/PDIF In (L/R Rev.)," functions identically to the third

option, except that the left and right channels are swapped. Therefore in

this mode, the left channel of the S/PDIF In is routed to OUT2 and the right

channel of the S/PDIF In is routed to OUT1.

5. Selections five through eight connect the hardware analog inputs 1 & 2, 3 &

4, 5 & 6, or 7 & 8 (respectively) directly to the 1010LT’s hardware analog

outputs 1 & 2. For example, if "H/W In 1/2" were selected, any signal

present at the IN1 port will be copied to OUT1, and any signal present at the

IN2 port will be copied to OUT2. This same behavior applies to "H/W In

3/4," "H/W In 5/6," and "H/W In 7/8" when selected.

The next three vertical columns of the Patchbay/Router page (from left to right), "H/W

Out 3/4," "H/W Out 5/6," and "H/W Out 7/8," connect these hardware analog outputs to

one of four sources. Since the three columns function identically, we’ll use "H/W Out 3/4"

as the example:

1. The default setting, "WavOut 3/4," connects ports OUT3 and OUT4 to your

music software or Windows multimedia applet. In other words, when music

software plays audio to the device named "WavOut 3/4 Delta-1010LT" it will

be routed directly to the "hardware" analog outputs 3 & 4 of your 1010LT

breakout cable.

2. The second option, "S/PDIF In," connects ports OUT3 and OUT4 directly to

the hardware S/PDIF input on the Delta 1010LT PCI host card. The left

channel of the S/PDIF In is routed to OUT3 and the right channel of the

S/PDIF In is routed to OUT4.

3. The third option, "S/PDIF In (L/R Rev.)," functions identically to the second

option, except that the left and right channels are swapped. Therefore in this

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 58 59

Comments to this Manuals

No comments

M-Audio DELTA 1010LT Specifications Page 22

Comments to this Manuals