M-Audio FireWire 410 Technical Information

Table of Contents1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Once the Bootloader installation is complete, Windows will locate the FireWire 410 driver files. The New Hardware Wizard will run a secondtime to inst

Once the installer has finished copying the files, you will see the Installation Complete screen. Once the installer has finished copying the files, y

Once again, select the default selection, “Install the software automatically” and click Next. Windows will install the driver files. You will againbe

3. Double click on the FireWire 410 icon. The file M-Audio FireWire 410 Installer.mpkg will appear. Double click on the installer file.4. You will nee

6. The next window "Welcomes You..." to the installation process. Click "Continue."7. Select your OS X hard drive. Click "Con

1. Insert the FireWire 410 driver CD into your CD-ROM drive. AutoRun will open the CD and allow you to view its contents.2. Double click on the “M-Aud

ATTENTION: You must shut down your computer any time you wish to connect or disconnect the FireWire 1814 from the system. Failure todo so may cause da

MIDIConnect your MIDI device’s MIDI Input to the FireWire 410’s MIDI Output. Connect your MIDI device’s MIDI Output to the FireWire 410’s MIDI Input.U

The FireWire 410’s driver software provides a simple yet powerful interface with your computer and Digital Audio Workstation software. Thecontrol pane

Mixer PageThe MIXER PAGE provides output routing and control of the FireWire 410’s analog and digital inputs, as well as the ten virtual channelsretur

Thanks for choosing the M-Audio FireWire 410 Mobile Recording interface. We designed the FireWire 410 to be a professional, portablesolution for getti

Output PageThe OUTPUT page provides you with control over each of the FireWire 410’s analog and digital outputs, as well as that of the AUX BUS andHEA

HEADPHONE MONITOR ASSIGNS – You can monitor any of the FireWire 410’s output buses via the Headphones bus. Using the MONITORASSIGNS you can select any

The following sections address a number of real-life situations that you may encounter while using your FireWire 410. These brief tutorialsshould help

If your audio application supports ASIO tape-type monitoring, you can enable it in your DAW’s ASIO or audio control panel. Please refer toyour audio s

Adding Effects While Direct MonitoringThis is an important feature of the FireWire 410, and something that sets if apart from many other audio interfa

2. In the FireWire 410 Mixer, add level to the AUX L and AUX R controls to create the headphone mix. Whichever channels are playing backinto the Mixer

The FireWire 410 has been designed to give you high performance and professional quality audio. It has been tested under a wide rangeof systems and op

13. Contact Us27M-AUDIO U.S.45 E. Saint Joseph St.Arcadia, CA 91006-2861 U.S.A.Sales Information: 626-445-2842Sales Information (email): info@m-audi

• Frequency response 20-40kHz ± 1 dB.• Signal to noise–108 dB• Dynamic range: 108 dB (A-weighted)• THD + N: 0.00281% @ 0 dBFSDefault settings:1) All m

M-AUDIO warrants this product, under normal use, to be free of defects in materials and workmanship for a period of One (1) Year from dateof purchase,

The FireWire 410 functions as a four-input, ten-output digital recording and playback interface. A single IEEE 1394 cable connects the FireWire410 to

30

31

32

• Dual low-noise mic/instrument preamps with gain controls, LED metering, phantom power and 66dB of available gain• Two analog inputs and eight analog

On the Mac, the FireWire 410 is supported under MacOS 9.2 or later, and Mac OSX version 10.1.5 or later. Earlier versions of Mac operatingsystems are

Front PanelRear PanelFront Panel descriptions1. MIC/INST INPUTS – Unbalanced Instrument and Mic level inputs. These Neutrik hybrid connectors will acc

•Phones – The level of the FireWire 410’s headphone outputs•Aux Send – The level of the FireWire 410’s AUX SEND bus, as controlled by the Input Channe

Win XPInsert the FireWire 410 driver CD-ROM into your computer. From the Start menu, select “Run…” then click the Browse button. Browse to theCD drive

The installer will prompt you to enable DVD/CD performance enhancement settings. In most cases you should leave these in their default(selected) setti