User’s GuideIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2M-Audio Ozone Features . . . .
8. An M-Audio Setup Window will appear to confirm a successful setup.Click “Next” to complete installation of the M-Audio Ozone.9. Windows will prompt
12. Another Windows Logo Testing window will appear. Click “ContinueAnyway” to continue.13. The next window informs you that the wizard has finishe
15. The “Found New Hardware Wizard” will again appear. Click “Next”to continue.16. Another Windows Logo Testing window will appear. Click “Continue
on your computer. Proceed with the DirectX installation byclicking, "Next.”2. Verify that you wish to continue installing DirectX 8.1 by clicking
5. This is the first setup window for installing the M-Audio Ozone driversafter the installer has confirmed that you have DirectX version 8.1 (orhighe
8. An M-Audio Setup Window will come up, confirming a successful setup.Click,“Next,” to successfully install the M-Audio Ozone.9. Windows will prompt
Windows ME:Note: Windows ME comes installed with DirectX version 7. You must haveDirectX version 8.1 in order to install the M-Audio Ozone. The M-Audi
4. Windows will need to restart your machine to complete the Direct X8.1 installation. Click, "OK," to restart your system.5. This is the fi
7. An M-Audio Setup Window will come up confirming a successful setup.Click,“Next,” to successfully install the M-Audio Ozone.8. Windows will prompt y
installation (if you have not previously installed this update). Click“Next” to install DirectX 8.1.4. Click next to verify that you would like to ins
IntroductionCongratulations on your purchase of the M-Audio Ozone. The M-AudioOzone is an innovative product—a powerful combination of MIDIcontroller
7. After restart, the next window reminds you to verify that the M-AudioOzone is disconnected from the USB bus before continuing, and that youhave clo
10. The following window prompts you to restart your computer.With thecheckmark enabled, click “Finish” to restart.11. After Windows has completely re
13. The next window defaults to browse to a specified location. Click“Next” to continue.14. In the next window, click “Next” to install the recommende
16. The final window tells you that installation is complete. Click “Finish”..After a few more ‘automatic’ windows which do not require any action, th
OMS InstallationTo install OMS from the driver CD, locate the OMS 2.3.8 folder on this CD,find the OMS installer program in the folder, and double c
BEFORE YOU RUN THIS INSTALLER PROGRAM. Otherwise, theM-Audio Ozone OMS Driver will not be placed in the OMS folder.Once installed, you should have two
4. The “OMS Driver Search” box asks you to choose the port on whichyou’ve attached the M-Audio Ozone (either Modem or Printer). DONOT choose a port (s
7. Next,“My Studio Setup” appears with a file save dialog box over it. Youwill now need to name and save your new studio setup (or use thedefault name
1. Go to "System Preferences" in the Apple Menu.2. Select the "Sound" preference panel, and click the "Output" tab.3. Se
Active Channels: A box that is checked indicates that a channel pair isset to “Active.” Unchecking a box will deactivate that channel pair. Whenthe Co
addition of eight programmable rotary knobs) allow it to send virtually anytype of MIDI controller information. Additionally, the M-Audio Ozone canope
Connection Status: The M-Audio Ozone Control Panel will only beaccessible when your M-Audio Ozone is connected to the computer andrecognized by the sy
sure that the M-Audio Ozone audio driver is set to “M-Audio Ozone ASIO.” Within your music application, when you assign an audio track to receiveits i
Each 1/4” line out jack (Output 1 and 2) sends a -10dB unbalanced signalon 1/4” TS plugs (tip-sleeve).They are designed to be plugged into a mixer,st
Using the Mic and Instrument InputsChannel 1 of the M-Audio Ozone gives you a high gain, low noisemicrophone preamp. It provides a low impedance micro
Setting Input GainThe M-Audio Ozone provides up to 60dB of gain on the Channel 1 Mic Inand 40dB of gain on the Channel 2 Instrument In. Microphones ty
to be safe, check your mic’s documentation to see if it will accept or needsphantom power. Some ribbon mics definitely should NOT receivephantom power
Also, as we mentioned, using Record mode defeats the Mic and Instrumentinputs, so you will not be able to listen to or record from those inputswhen th
monitoring, mute the channels you are recording to, or send their outputto another bus.In a typical Direct Monitor application, plug your microphone a
In the following setup, the M-Audio Ozone is being used as a MIDIcontroller as well as a MIDI interface, inputting MIDI data to the computerand its ap
The keys on the M-Audio Ozone, in conjunction with the MIDI/SELECTbutton, give you the extra programming capability that is unique toM-Audio’s line of
Guide to Getting StartedHere is an outline of the steps needed to begin using your M-Audio Ozoneon either a Mac or a PC:1. Install the Driver (see “So
of your choice, send program change data from the keyboard, select theMIDI transmit channel of the M-Audio Ozone, set the octave or pitch ofthe keyboa
4. Assign the MIDI channel number on number key group (1-16) thenpress Enter. This channel assignment will apply only to the controllerknob that you a
5. Press the CC Data key.6. Press the number keys 1, 2 and 3, in order.7. Press the Enter key, to specify the value 123, then press theMIDI/SELECT but
M-Audio Ozone Preset Chart44
Technical Support & Contact InformationFor additional technical assistance, contact M-Audio Technical Support bytelephone (626-445-8495, 9-5 PST M
M-Audio Ozone Warranty InformationM-AUDIO warrants that this product is free of defects in materials andworkmanship under normal conditions for 90 day
M-Audio Ozone Technical SpecificationsGeneral• Supports 24-bit or 16-bit audio input or output• Supports the following sampling frequencies (Hz): 8000
Appendix A - MIDI Controller Information48
Appendix B - M-Audio Ozone Block Diagram49
3. Data Entry Slider:This slide controller allows you to adjust the value ofparameters such as Volume, Velocity, Aftertouch, and virtually anyassignab
Rear Panel1. Power Switch: The Power Switch turns on the M-Audio Ozone. Youprobably figured that one out for yourself.2. Power Jack:This jack is used
12. Mic In (Channel 1): This is an XLR Balanced preamp input formicrophones. Mic In preamp gain is controlled by the top panel “MicGain” control.This
Windows XP:1. The M-Audio Driver CD should be inserted into the computer's CD-ROMdrive. In this example the CD-ROM drive is letter "D."
5. Another “Digital Signature Not Found” Window will appear. Click“Continue Anyway” to continue.6. Another “Digital Signature Not Found” Window will a
Comments to this Manuals